Charge A Tl9673 Handset Without Registering First?

Skip to content

If your Uniden production is not performing to your expectations, delight try these unproblematic steps. If y'all are still unable to resolve the problems, delight contact Uniden Customer Service for assistance.

CHARGING/POWER

Charge light won't come on when Handset is placed in the Base Unit?

• Brand sure AC Adapter is plugged into the phone Base Unit and the wall outlet.
• Make sure Handset is properly seated in Base Unit.
• Make sure that the charging contacts on the Handset and Base Unit are make clean.

There are no lights on the Base of operations Unit?

Make sure the AC adaptor is continued to electrical power at all times.

The phone only operated after the commencement fourth dimension the handset was charged?

Make certain the AC adaptor is continued to electrical ability at all times and the handset is recharged regularly.

The batteries do non work in my new cordless telephone?

The batteries need an initial uninterrupted charge of 15-20 hours before use.

The charging calorie-free colour does not modify when the batteries are fully charged?

This is normal. It is non meant to change color.

Should I leave the handset back on the base subsequently the batteries are fully recharged?

There is no problem in leaving the handset back on the base all the time, fifty-fifty subsequently short periods of usage. It will not grade a retention consequence. Nonetheless, information technology is recommended that once every 3 months discharge the batteries completely (by leaving the handset off the base of operations. Utilise the telephone as you would usually until the bombardment low light starts flashing) and and so elevation upwards the charge again for 15-20 hours.

The handset beeps?

Recharge the battery for xv-20 hours. Check to see that the battery in the handset is continued properly. If it continues to beep the battery may need replacing.

AUDIO QUALITY

Audio sounds weak and/or scratchy. Interference is evident on my analogue phone?

• Make certain that the Base Unit of measurement antenna is fully extended and vertical.
• Move the Handset and/or Base Unit of measurement to different locations and try again.
• Press the (chan) button (if available on the keypad) to select another aqueduct.
• Brand sure no other device is sharing the aforementioned AC power outlet as the cordless phone.

Interference is axiomatic on my digital phone?

Move whatsoever metal objects abroad from the base of operations. Brand sure no other device is sharing the same Air-conditioning power outlet as the cordless phone.

Only continuous static is heard from the Handset and the phone volition not turn off?

• The power has been interrupted during a phone call.
• Restore power to the Base of operations Unit.
• If a power failure has occurred and power volition exist out for some fourth dimension, remove the battery from the Handset. This will preclude the battery from completely discharging.

The handset and base of operations make a humming noise?

Disconnect the AC adaptor from the back of the Base of operations Unit and re-connect it after five minutes.

NO CALLS

Can't brand or receive calls. At that place is no dial tone?

• Check that both ends of the Base Unit telephone line cord are continued
• Make sure the Ac Adapter is plugged into the Base Unit and wall outlet.
• Make sure the battery in your handset in connected properly
• Disconnect the AC Adapter for a few minutes, and so reconnect it and ensure the power is turned on.

RINGING

Handset does non ring or receive a folio?

• Nickel-Cadmium battery pack may be weak. Clean the contacts on the Base Unit. Charge the battery on the Base of operations Unit for xv-20 hours.
• Extend the Base Unit of measurement antenna vertically.
• The Handset may exist likewise far away from the Base Unit.
• Identify the Base Unit away from racket sources.
• Brand sure the AC adaptor is plugged in and turned on.
• The Digital Security Lawmaking may be erased. Gear up the Digital Code (see the Phone's Operating Transmission)

The Base Unit of measurement does not band?

Make sure the base of operations unit ringer switch is non on the LO or OFF position. Switch it to Hi.

CALLER ID

How do I activate caller ID?

Contact your service provider to arrange this (eg Telstra, Optus, Telecom etc). Without subscribing, this service volition not operate.

How can I access call waiting?

When y'all hear the call waiting signal press 'Flash' and then Number two, which will automatically choice upward this second caller. The first/original caller will be placed on concur. To switch dorsum to the commencement caller press 'Flash' and Number one. Make sure that the phone is on tone setting.

Telephone call waiting is not working?

Make sure the T / P switch on the base unit is in the tone position. Also cheque with your service provider that y'all have telephone call waiting activated.

Full general OPERATION

Range is limited?

Make sure no other appliance is sharing the same power outlet. Extend the antenna fully on the base of operations unit.

The answering machine is non answering calls?

Make sure the REC TIME is not positioned in the ANN position on the Base Unit.

Telephone banking is not working?

Brand sure the T / P switch on the base is on the T- tone position.

How exercise I extend the number of rings?

Printing the answer push on the base (answer off), this will requite you upwards to fifteen rings before the answering machine turns on and takes the message.

The clock on the answering machine looses time?

Reset your answering machine and reset the clock again. Make sure the base unit of measurement has an uninterrupted power source.

I cannot record an outgoing message?

The memory may be full. Delete some of your stored messages or reset your answering machine and re-tape your outgoing message.

How do you store phone numbers to retentiveness?

Press the Retentiveness fundamental, followed by the telephone number you lot wish to store, then printing the Memory key once again and then the number location to which you wish to store this number.

Will my phone work overseas?

No, it has been engineered and powered for Australian weather only.

What practise I exercise if my telephone gets wet?

Unplug all leads, dry out the unit as best you can and have the unit of measurement for service immediately.

The earpiece volume is not loud enough?

Press the Volume button during a call to alter the audio level.

The ringer volume is non loud enough?

Press the Book button while the phone is not in use to change the ringer volume.

Go to Top

SUBSCRIBE TO OUR NEWSLETTER

Receive the latest Product Releases, Competitions and Deals.

Charge A Tl9673 Handset Without Registering First?,

Source: https://uniden.com.au/faqs/

Posted by: bullardwhictime.blogspot.com

Share this post